No audio at relay

[t3f]

Hello,

i have searched since to days and i have no answer about my question.

my target ist that i have a Master-Host where runs the sc_trans (from 14_12_2010) and the sc_serv (24_02_2011). This Master has one client/relay with sc_serv2 (from 25_02_2011).

The different versions from the two sc_serv2 process is the problem when i used on both process the 24_02_2011 or the 25_02_2011 version i get a "Segmentation fault" error. With two differnet versions i have no problem there.

the most problem is that on the master i have all the streams i had configuried, but on the relay i have only one stream and that stream have no sound.

debug is set on all serv and trans processes to 1.

Config for the master sc_serv2 process

PHP Code:

;config

password=*****
maxuser=100000
adminpassword=*****
flashpolicyfile=/home/admin1/shoutcast/serv/crossdomain.xml
requirestreamconfigs=1
logfile=/home/admin1/shoutcast/serv/sc_serv.log
w3clog=/home/admin1/shoutcast/serv/sc_w3c.log
banfile=/home/admin1/shoutcast/serv/sc_serv.ban
ripfile=/home/admin1/shoutcast/serv/sc_serv.rip
RelayServer=192.168.185.48
RelayPort=8000

streamid_1=1
streampath_1=/listen1
maxuser_1=50000

streamid_2=2
streampath_2=/listen2
maxuser_1=50000

streamid_3=2
streampath_3=/listen3
maxuser_3=50000
publicServer=never
allowrelay=1 


Config for the relay sc_serv2 process:

PHP Code:

;config

password=*****
maxuser=1000
adminpassword=******
flashpolicyfile=/home/admin1/shoutcast/serv/crossdomain.xml
requirestreamconfigs=1
logfile=/home/admin1/shoutcast/serv/sc_serv.log
w3clog=/home/admin1/shoutcast/serv/sc_w3c.log
banfile=/home/admin1/shoutcast/serv/sc_serv.ban
ripfile=/home/admin1/shoutcast/serv/sc_serv.rip
publicserver=never

relayserver=192.168.185.48
relayport=8000 


At now i tried this on two physical machines on the same subnet and without any firewall or gateway.

Do you have any ideas for that problem?

[DrO]

the first thing that jumps out is you're using the legacy way of specifying a relay rather than the streamrelayurl method as should be used with the v2 tools (as you're using).

other than that, i'm really struggling to follow how / what you've setup on the different machines especially with swapping around between versions.

-daz

[t3f]

>the first thing that jumps out is you're using the legacy way of specifying a relay rather than
>the streamrelayurl method as should be used with the v2 tools (as you're using).

i have tryied different versions of relay a stream. one of my test was

PHP Code:

relayserver=192.168.185.48
relayport=8000 


another test was this

PHP Code:

streamid_1=1
streampath_1=/listen1
streamrelayurl_1=http://192.168.185.48:8000/ 


but none of them doesn't turn the audio on.


> other than that, i'm really struggling to follow how / what you've setup on the different
> machines especially with swapping around between versions.

I have two servers

one is 192.168.185.48 (master)
on this server the version (24_02_2011) for serv2 and the transcoder with version 14_12_2011 runs perfectly.

second server 192.168.185.123 (relay)
i have tryied to start the sc_serv2 process and after startup and try to connect to master there comes the error "Segmentation fault".
i searched but no answer or solution found. because i have no idea i tryied to start with the new version and this starts with the same configuration. but only when the master has a different version than the relay??

PHP Code:

2011-03-01 14:42:30     D       msg:protocol_relay_uvox
2011-03-01 14:42:30     D       msg:[THREADRUNNER] thread 2 amt=2
2011-03-01 14:42:30     D       msg:[THREADRUNNER] thread 1 amt=1
2011-03-01 14:42:30     D       msg:[THREADRUNNER] thread 3 amt=1
2011-03-01 14:42:30     D       msg:[THREADRUNNER] thread 0 amt=1
2011-03-01 14:42:30     D       msg:[THREADRUNNER] Adding protocol_relay_uvox to thread 1
Segmentation fault 


sorry for my english it's not the best

[DrO]

there shouldn't be a segfault happening though with all of the internal changes in the last few versions, it's possible you've found a legitimate issue so i'll try to replicate the issue.

one thing i will note is that there is a known issue where if you try to relay a server and have it listed on the YP then it wll not work - i see your configs have publicserver=never so that's not currently an issue but might become an issue if you then change it.

will see what i can do to reproduce the issue and will send you a test build in a few days (have a few other changes to implement first).

-daz

[t3f]

there shouldn't be a segfault happening though with all of the internal changes in the last few versions, it's possible you've found a legitimate issue so i'll try to replicate the issue.

one thing i will note is that there is a known issue where if you try to relay a server and have it listed on the YP then it wll not work - i see your configs have publicserver=never so that's not currently an issue but might become an issue if you then change it.

will see what i can do to reproduce the issue and will send you a test build in a few days (have a few other changes to implement first).

-daz

my configuration is on "ubuntu 10.04 LTS" with 32bit kernel. It's the standardconfig with ssh-server no other programs installed.

at the moment the configuration with publicserver=never is correct, this is a local test only and grow eventuelly later. then it goes to yp2.

can you recommence a version where i can try this feature?

- stefan

[DrO]

how you're doing it at the moment is the only way to try to test it (ignoring the issues you're experiencing).

there's a few things on the YP2 side of things which need to be changed to hopefully allow for relaying to work with a v2 setup (though it also requires a stable v2 DNAS so i need to fix the issue you're seeing so plans to hopefully resolve the issue can be started).

-daz